F4RT Powered Alien

[Roadrunner1100]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

Is that the one on your YouTube??? Crazy car!!

Yes, there are few more video but not on the internet Dont want stress with the cops

I understand. It looked and sounded Nice mate. Especially the big backfirr haha

 

[autoyasin]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

That’s one tidy bay!

I was toying of the idea of the golf gti TFSI lump into the twingo, very easily tuneable!

The megane engine is easy too. This is the log with the old injectors. Now there are 1000 ccm injectors.

https://picload.org/view/dappgpll/unbenannt.jpg.html

 

[autoyasin]

Here i uploaded a new video but for a short time

https://www.youtube.com/watch?v=sgQSIZC1MzE

https://www.youtube.com/watch?v=_IdqqeAQ1Qs

 

[Dave_133]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

That’s one tidy bay!

I was toying of the idea of the golf gti TFSI lump into the twingo, very easily tuneable!

The megane engine is easy too. This is the log with the old injectors. Now there are 1000 ccm injectors.

https://picload.org/view/dappgpll/unbenannt.jpg.html

Going to run mine for a while at the power it is, then see about more power afterwards. Not sure if I can justify chucking another say 5k or so at the car

 

[autoyasin]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

That’s one tidy bay!

I was toying of the idea of the golf gti TFSI lump into the twingo, very easily tuneable!

The megane engine is easy too. This is the log with the old injectors. Now there are 1000 ccm injectors.

https://picload.org/view/dappgpll/unbenannt.jpg.html

Going to run mine for a while at the power it is, then see about more power afterwards. Not sure if I can justify chucking another say 5k or so at the car

I ve spend in 5 years 50k into the audi engine (only) But it has a lot of horses and capable of 1700 hp with the setup, it is my hobby. On the dyno video it has 1250 horses with 3.5 bar boost and can boost up to 4.5 bar. You can spend your money into everything but my heart beats for my cars
I think 500 horses in the Twingo is the drivable limit.

 

[Roadrunner1100]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

That’s one tidy bay!

I was toying of the idea of the golf gti TFSI lump into the twingo, very easily tuneable!

The megane engine is easy too. This is the log with the old injectors. Now there are 1000 ccm injectors.

https://picload.org/view/dappgpll/unbenannt.jpg.html

Going to run mine for a while at the power it is, then see about more power afterwards. Not sure if I can justify chucking another say 5k or so at the car

It’s running around 250 brake now right? Should be plenty mate, leave it and enjoy! If, after a while, you end up wanting more you can always do it.

 

[Dave_133]

Or you put a inline 5 audi 20v in the Trs and make some boost This is my first Project, the TRS is the third. The Audi is only for Drag racing and Roll race.

https://picload.org/view/dappgiri/img_20170727_165900.jpg.html

That’s one tidy bay!

I was toying of the idea of the golf gti TFSI lump into the twingo, very easily tuneable!

The megane engine is easy too. This is the log with the old injectors. Now there are 1000 ccm injectors.

https://picload.org/view/dappgpll/unbenannt.jpg.html

Going to run mine for a while at the power it is, then see about more power afterwards. Not sure if I can justify chucking another say 5k or so at the car

It’s running around 250 brake now right? Should be plenty mate, leave it and enjoy! If, after a while, you end up wanting more you can always do it.

Yeah it’s 252 bhp at the moment. Plenty of room for improvement there tho!

 

[autoyasin]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

 

[Roadrunner1100]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Looking good!

 

[Dave_133]

Tool arrived today, swapped the files over (eventually) still got an error code re throttle track 1. Can only think the throttle body is at fault as I didn’t have this at all on my four hour drive back.

Going to investigate over the weekend and see if I can get my hands on one to swap and test with.

 

[Dave_133]

So another update for today, I quickly took the throttle body off and cleaned it all up. Cleaned the connector for it and also the connector on the pedal itself. Was no longer in limp mode! However once I got up the road it went back into it again *sigh*

But on a positive note the file change on the ECU was a success and I no longer have the car cutting out due to traction, so was able to give it a bit of a trashing [emoji41]

Should hopefully have a new throttle body by next week so that should eliminate that! If not I’ll have to have a look at the wiring.

 

[Miller]

I'm glad your making progress with the problem. Never the easiest things to get to the bottom of.

 

[autoyasin]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Looking good!

Ok i photographed the things in the engine bay.

You see on the first picture the 15 mm plate to lift the engine.

The second one is the torque link

The third one is the gearbox mount

Weldet the parts together an volai it is working

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

 

[Dave_133]

I'm glad your making progress with the problem. Never the easiest things to get to the bottom of.

Yeah hard enough on a standard car, let alone mine which has twingo ecu, megane engine and a clio throttle body

 

[Roadrunner1100]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Looking good!

Ok i photographed the things in the engine bay.

You see on the first picture the 15 mm plate to lift the engine.

The second one is the torque link

The third one is the gearbox mount

Weldet the parts together an volai it is working

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

That doesn’t look too hard right? Should be able to do it.. something keeps pulling me to the meg Engine and box hahaha. Is the meg 3 Engine Also compatible with the twingo ecu??

 

[Roadrunner1100]

I'm glad your making progress with the problem. Never the easiest things to get to the bottom of.

Yeah hard enough on a standard car, let alone mine which has twingo ecu, megane engine and a clio throttle body

Yeah you get a bit of a mismatch in parts haha but Im Sure you can solve it!

 

[autoyasin]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Looking good!

Ok i photographed the things in the engine bay.

You see on the first picture the 15 mm plate to lift the engine.

The second one is the torque link

The third one is the gearbox mount

Weldet the parts together an volai it is working

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

That doesn’t look too hard right? Should be able to do it.. something keeps pulling me to the meg Engine and box hahaha. Is the meg 3 Engine Also compatible with the twingo ecu??

the ecu is a problem if you want more boost. But i have a meg 3 rs ecu in my storage, if you want it, let me know. I use a standalone ecu. I programmed everything by myself.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

 

[Roadrunner1100]

Soo my mounts arived today. I hope it will be better to drive.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Looking good!

Ok i photographed the things in the engine bay.

You see on the first picture the 15 mm plate to lift the engine.

The second one is the torque link

The third one is the gearbox mount

Weldet the parts together an volai it is working

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

That doesn’t look too hard right? Should be able to do it.. something keeps pulling me to the meg Engine and box hahaha. Is the meg 3 Engine Also compatible with the twingo ecu??

the ecu is a problem if you want more boost. But i have a meg 3 rs ecu in my storage, if you want it, let me know. I use a standalone ecu. I programmed everything by myself.

Gesendet von meinem ONEPLUS A3003 mit Tapatalk

Id like to keep the twingo ecu for the electronics to work.. that’s Why I like the turbo setup on stock Engine.

 

[Dave_133]

So the car is dead again [emoji22] doing be exact same thing as before cutting all power. Seems like swapping the file over was just a short fix.

Getting slightly fed up with it now lol

 

[Roadrunner1100]

So the car is dead again [emoji22] doing be exact same thing as before cutting all power. Seems like swapping the file over was just a short fix.

Getting slightly fed up with it now lol

Damn.... Surely just a faulty sensor or wire somewhere?...